1

411 & 450 Himalayan & Scram / Re: 2019 Himalayan known issues

« Last Post by GSS on Today at 10:36:20 am »

Mostly easily fixable minor issues over the years.

1. Keyed ignition switch caused 2-3 random shut downs. Cleaned carbonized stuff off the contacts and put dielectric grease and there has been no recurrence. A few folks replaced the ignition switch instead.

2. Battery drains out in 1-2 weeks if unused. Hitchcock’s sells a little adapter that fixed this issue.

3. If in the US, RE did recall and replace both brake calipers for corrosion issues.

4. Front brake lever can go flat after a few days and no amount of bleeding by any manual technique fixes it. Needs the RE electronic tool to cycle ABS to get hidden air bubbles out, but this would have been already done during the caliper recall.

Overall a very reliable bike. HCM cam, powertronic and Lexmark muffler totally woke up the engine. Hope this helps. Thanks.

2

650 Interceptor & Continental GT / Re: Mid/forward controls for interceptor?

« Last Post by GSS on Today at 10:26:37 am »

HCM adjusters have worked perfectly for several years. Absolutely no issues with anything falling apart. They do push the entire controls further away from the bike….I took them off last week and am in the process of trying out the Triumph 100/120 original footpegs.

3

Bullet Iron Barrel / Re: PowerBox (single phase), query?

« Last Post by stinkwheel on Today at 09:55:48 am »

Makes an odd kind of sense. Someone lost the washer (easily done, I've had main jets unscrew themselves). Bike showing symptoms of low float height because the main jet is now sitting too high, adjust float height higher and bike runs properly but fuel is now coming out of the overflow, plug up overflow.

So once you get it assembled properly and verify the needle jet and main jet are now firmly where they should be and not wobbling/loose. I'd check the float height is correct. The only reson someone would deliberately block the overflow is if the float height is too high or the needle valve is leaking.

4

Bullet Iron Barrel / Re: PowerBox (single phase), query?

« Last Post by French MK on Today at 09:51:11 am »

Don't know if you read this bit? I edited later.

Also noticed the float bowl breather/overflow is capped off, surely that didnt help.

5

650 Interceptor & Continental GT / Re: What did you do to your bike today?

« Last Post by Inty in Sydney on Today at 07:45:50 am »

Installed a side bag instead of the cover

Ooooooh very nice! By the way, would appreciate when you get some time:
- a couple of pics of that seat to check proportions in relation to the bike
- what do you thing of it....good, meh...crap?

Have seen it before but nothing beats real world feedback. Thanks in advance.. ;-)

6

650 Interceptor & Continental GT / Re: What did you do to your bike today?

« Last Post by Inty in Sydney on Today at 07:22:50 am »

Nice.  Racetech is a good outfit.  I see they come in piggyback style too with compression adjustment.  I might have gone for those instead of the YSS if I had known they existed.

Would you happen to know what rate springs they put on those?  I'm curious because I recently ordered custom linear springs for my YSS ($$$) and had to guesstimate the rate.

Hey Yellow Duck...does this help... ;-)

Spring Main:1.8
Preload: 15mm
Sag; 34

7

650 Interceptor & Continental GT / Re: Weird “pop” sound after shutting INT650 off..

« Last Post by Re-Cycle on Today at 07:00:34 am »

Just curious, but why would you use the killswitch to turn the bike off and not the key?

As you have guessed I use the key  and have never noticed any sound after turning off except the tick-tick of the exhausts cooling down.

8

650 Interceptor & Continental GT / Re: What did you do to your bike today?

« Last Post by andif62 on Today at 05:42:19 am »

Installed a side bag instead of the cover

9

650 Interceptor & Continental GT / Re: Anyone have the AEW 2-1 Exhaust? Comparing to TEC 2-1

« Last Post by BlackdogADV on Today at 05:11:02 am »

I wish it was available in black.  Is it a brushed or shiny finish?

10

350 J Platform / Re: Classic 350 Reborn - Handlebar Riser?

« Last Post by BC_Rob on Today at 04:40:32 am »

Perfect… thanks for posting the link.