Author Topic: Handle bars on a G5 Military.  (Read 3084 times)

0 Members and 1 Guest are viewing this topic.

Ragmas

  • Grease Monkey
  • ****
  • Posts: 358
  • Karma: 0
on: August 31, 2010, 05:20:30 pm
I would like my bars to be pulled back a couple of more inches than they are.  The ones on the bike are stock 2009 G5 Military.  Does anyone know what bars would give a bit more pull back?

Thanks,

Sam
2009 G-5 Military
Little Falls, NY


UncleErnie

  • Grand Gearhead
  • *****
  • Posts: 2,533
  • Karma: 0
Reply #1 on: August 31, 2010, 05:35:33 pm
Most bike shops have a Tucker Rocky catalogue you can look in.  Bike Master bars are around $25 and have different shapes.  Measurements are given.
Run what ya brung


jjoe256

  • Grease Monkey
  • ****
  • Posts: 420
  • Karma: 0
Reply #2 on: August 31, 2010, 07:08:35 pm
Here's a comprehensive catalog with measurements so take your pick. I wound up putting Kawasaki Police Bars on an Aprilia Falco street fighter!!

http://www.flandersco.com/about.html


ScooterBob

  • Grand Gearhead
  • *****
  • Posts: 2,559
  • Karma: 0
  • Yeah - I get it ....
Reply #3 on: September 01, 2010, 01:10:37 am
I would like my bars to be pulled back a couple of more inches than they are.  The ones on the bike are stock 2009 G5 Military.  Does anyone know what bars would give a bit more pull back?

Thanks,

Sam

P/N 560538 .......
Spare the pig iron - spoil the part!


3rdgear

  • Scooter
  • **
  • Posts: 51
  • Karma: 0
Reply #4 on: September 26, 2010, 02:07:49 am
Ragmas: did you find the bars you were looking for?  I'm in the same boat. Would like a bar like a beach cruiser bicycle might have.
« Last Edit: September 26, 2010, 02:10:08 am by 3rdgear »


3rdgear

  • Scooter
  • **
  • Posts: 51
  • Karma: 0
Reply #5 on: September 26, 2010, 02:11:58 am
P/N 560538 .......

I searched for this part number on Flanders site.  Unable to find it.  If you could post a link, I would like to see what it looks like.

Thanks.


qgolden

  • Grease Monkey
  • ****
  • Posts: 302
  • Karma: 0
  • It takes a villiage to raise an idiot.....
Reply #6 on: September 26, 2010, 02:47:12 am
I searched for this part number on Flanders site. 

Aint a gonna' find it on the Flanders site, it is a NField part number.
Any other Enfields in New England?


Ducati Scotty

  • Grand Gearhead
  • *****
  • Posts: 7,038
  • Karma: 0
  • 2010 Teal C5
Reply #7 on: September 26, 2010, 06:42:01 am
Remember, you may need longer cables if you get way outside the stock bend/length.

Scott


Ragmas

  • Grease Monkey
  • ****
  • Posts: 358
  • Karma: 0
Reply #8 on: September 26, 2010, 09:09:51 pm
I have not found bars yet.  As it turns out I have a friend who has a friend with lots of motorcycle parts.  I am going to get an assortment from him and see if I can make a go at it.

Sam
2009 G-5 Military
Little Falls, NY